grml debnet Search through local partitions for file /etc/network/interfaces,
copy /etc/network to local system and restart networking then
grml dns=8.8.8.8,8.8.4.4 Set DNS resolvers during boot and for live system.
+grml ip=... Standard Linux kernel ip= boot option. Arguments:
+ clientip:nfsserverip:gwip:netmask:hostname:device:autoconf
+ Valid values for autoconf: off, on, dhcp, bootp, rarp, both.
+ Almost everything is optional. Most common form: ip=dhcp
grml mypath=... Add specified option into $PATH of Zsh
For example when using "grml mypath=/foobar" then /foobar
will be added to the end of $PATH inside Zsh
the directory are executed.
grml config=path-name Unpack archive that path-name points to
grml noautoconfig Disable searching for device labeled GRMLCFG
+grml nobeep Disable welcome chime, sounded before grml-quickconfig starts.
Notice: Take a look at http://grml.org/config/ and 'man 1 grml-autoconfig'
for more information regarding the configuration framework of Grml.
grml nogpm Disable GPM daemon
grml noconsolefont Disable setting of console font (using consolechars)
grml noblank Disable console blanking
-grml tsplash Text based bootsplash
grml noquick Disable grml-quickconfig startup script
grml small Do not start that many consoles
grml wondershaper=eth0,1000,500 Set up basic traffic shaping
which decide to enable startx by default only, plain grml does not use
automatic startup of X by default.)
-Accessibility related settings:
--------------------------------
-grml blind Start Braille-Terminal (no X)
-grml hwspeak Probe all available speakup hardware modules
-grml swspeak Prepare system for use with software synthesizer through speakup
- Run 'swspeak' after booting up to activate sound output
-grml swspeak=espeak Use espeakup (if available) as connector to speakup
- Run 'swspeak' after booting up to activate sound output
-grml swspeak=speechd Use speech-dispatcher / speechd-up (if available) as connector to speakup
- Run 'swspeak' after booting up to activate sound output
-grml brltty=type,port,table Parameters for Braille device (e.g.: brltty=al,/dev/ttyS0,text.de.tbl)
-grml speakup.synth=... Use speakup kernel module with given hardware type
- Usage example: speakup.synth=apollo
-
Hardware related settings:
--------------------------
grml swap Activate present/detected swap partitions
grml xmodule=ati|fbdev|i810|mga Use specified X.org-Module (1)
grml xmodule=nv|radeon|savage|s3 Use specified X.org-Module (2)
grml xmodule=radeon|svga|i810 Use specified X.org-Module (3)
-grml no{acpi,agp,apm,cpu,dhcp} Skip parts of HW-detection (1)
+grml no{acpi,agp,cpu,dhcp} Skip parts of HW-detection (1)
grml no{dma,fstab,modem} Skip parts of HW-detection (2)
grml no{pcmcia,scsi,swap,usb} Skip parts of HW-detection (3)
-grml 915resolution=... Start resolution modify tool for Intel graphic chipset
- usage: $MODE,$XRESO,$YRESO
grml blacklist=modulename[,module2] Completely disable loading of specified module(s) via
blacklisting through udev's /etc/modprobe.d/grml
grml fwtimeout=50 Set firmware timeout via /sys/class/firmware/timeout to specified value
grml micvol=number Set mixer volume of microphone to level $number (default: 0)
grml pnpbios=off No PnP Bios initialization
grml acpi=off Disable ACPI Bios completely
-grml nousb2 Disable initialization of USB 2.x controller(s)
-grml nousb Disable initialization of USB in booting sequence
grml nofirewire Disable initialization of firewire devices in booting sequence
grml pci=irqmask=0x0e98 Try this, if PS/2 mouse doesn't work *)
grml pci=bios Workaround for bad PCI controllers
Installation related settings:
------------------------------
-Caution: do *NOT* use the grml2hd and/or debian2hd bootoption if you do not know what you are doing!
+Caution: do *NOT* use the debian2hd bootoption if you do not know what you are doing!
Install plain Debian via debian2hd bootoption (which runs grml-debootstrap in non-interactive mode):
See http://grml.org/grml-debootstrap/ for more information.
-Install grml via grml2hd bootoption (which runs grml2hd in non-interactive mode):
-
-grml2hd <options> ... whereas valid options for grml2hd are:
-
- user= user name for user which should be used at hd-install
- filesystem={ext2|ext3|reiserfs|reiser4|jfs|xfs} filesystem to be used
- mbr=/dev/... partition where MBR should be installed (default:=partition)
- partition=/dev/... partition where grml should be installed
-
- Usage example for booting:
- grml2hd partition=/dev/sda4 mbr=/dev/sda filesystem=ext3 user=mika
-
- Passwords of user root and user are "grml" - please adjust after hd-install!
-
- See http://grml.org/grml2hd/ for more information.
-
Additional notes:
-----------------
*) In case of a failing hardware autodetection, try booting with any of
the "no-" options as shown in the table above, like in
- grml noagp noapm noapic acpi=off nodma
+ grml noagp noapic acpi=off nodma
to skip some critical parts of the autodetection system.
*) Some boards (especially those with E-ISA slots) apparently don't pass